Bluetooth HC-05 AT Command mode using Arduino Uno

This is a video on how to enter the command mode of HC-05 Bluetooth module using arduino uno.
For Connection, code and AT command click the link below.
https://drive.google.com/drive/folders/0B3GPRO1RK6cWZnpvNk9EUW1kR2c?usp=sharing

source

Arduino/Android BLUETOOTH Serial Monitor APP for arduino using the HC-06 and ANDROID

Hello world! Today i made a Android app that simply reads values or text that are printed to the arduino serial using bluetooth module HC-06/05 or other modules. You don’t need to set anything in the arduino code. Just simply Serial.println will display the value or text in the android app. Follow the link for the instructable, schematic, example code and google play app! http://www.instructables.com/id/ArduinoAndroid-BLUETOOTH-Serial-Monitor-APP-for-Ar/

source

Arduino – BLUETOOTH & ANDROID PIR ALARM with call and sms Functions!

Hello world! Today i made a android app that communicates with a arduino using the HC-06 Bluetooth module for a PIR Motion sensor GSM Alarm. You can set 1 phonenumber to the DATABASE that needs to be called when movement is detected. When movement is detected it will call you and you can listen what is happening in your home, If you missed the call you can send a SMS with the command “Call me” (it is case sensitive, so use capital C). You can also send a SMS command with “Disconnect” and the bluetooth module will disconnect. For the Schematic, Arduino Code, Android APP & Parts list follow the next link: http://www.instructables.com/id/Arduino-BLUETOOTH-ANDROID-PIR-ALARM-With-Call-and-/

NOTE: You need to take a few steps for the APP to operate properly and you need to connect the Phone to a Charger.

Follow these next steps on your Android phone.
1: Settings, go to call, extra settings, turn off proximity sensor.
(Turns off screen during calls when on, and we want the screen to be on)

2: Settings, Location & security, setup screen lock to none.

3: Settings, Applications, development, turn on standby or might be named stay awake on your phone
(keeps screen on during Charging)

Check out our website! http://www.arduinosensors.nl
Check out our Forum! http://Forum.arduinosensors.nl

source

Arduino Tutorial – LCD Display Control via Bluetooth (Part2)

How to control an LCD via Bluetooth

First watch this video:

Hardware Required

– Arduino or Genuino Board
– LCD Screen
– HC06-05 Bluetooth Module
– Pin headers to solder to the LCD display pins
– 10k ohm potentiometer
– 220 ohm resistor
– hook-up wires
– breadboard

Flash Deals — https://goo.gl/CVqg7P
Mega Stock Clearance — https://goo.gl/eCbuiP
Arduino Kits — https://goo.gl/uwr19e
Anet A8 3D Printer Promotion — https://goo.gl/MNa3p9
More Budget 3D Printers — https://goo.gl/v6fPU4

The LCDs have a parallel interface, meaning that the microcontroller has to manipulate several interface pins at once to control the display. The interface consists of the following pins:

– A register select (RS) pin that controls where in the LCD’s memory you’re writing data to. You can select either the data register, which holds what goes on the screen, or an instruction register, which is where the LCD’s controller looks for instructions on what to do next.
– A Read/Write (R/W) pin that selects reading mode or writing mode
– An Enable pin that enables writing to the registers
– 8 data pins (D0 -D7). The states of these pins (high or low) are the bits that you’re writing to a register when you write, or the values you’re reading when you read.
– There’s also a display constrast pin (Vo), power supply pins (+5V and Gnd) and LED Backlight (Bklt+ and BKlt-) pins that you can use to power the LCD, control the display contrast, and turn on and off the LED backlight, respectively.

Circuit

Before wiring the LCD screen to your Arduino or Genuino board we suggest to solder a pin header strip to the 14 (or 16) pin count connector of the LCD screen.
To wire your LCD screen to your board, connect the following pins:

LCD VSS pin to Arduino GND
LCD VDD pin to Arduino 5V
LCD RS pin to digital pin 12
LCD RW pin to Arduino GND
LCD Enable pin to digital pin 11
LCD D4 pin to digital pin 5
LCD D5 pin to digital pin 4
LCD D6 pin to digital pin 3
LCD D7 pin to digital pin 2
Additionally, wire a 10k pot to +5V and GND, with it’s wiper (output) to LCD screens VO pin (pin3).
A 220 ohm resistor is used to power the backlight of the display, usually on pin 15 (A+) and 16 (K-) of the LCD connector.

Get the Code and Application:
http://mertarduinotutorial.blogspot.com.tr/2016/12/arduino-tutorial-11-lcd-control-via.html

App Inventor
http://appinventor.mit.edu/explore/

source

Lamps controlling by Android phone using Arduino & hc-05 Bluetooth module hindi tutorial

घरेलु उपकरणों को एंड्राइड फोन से चालू और बंद करे।
Arduino uno और hc-05 Bluetooth module का उपयोग करते हुये ।
Arduino Code

https://drive.google.com/file/d/0B_TaVit2pXZIYm1nWFBXRXlzd3M/view?usp=drivesdk

source

Arduino RGB LED control using Bluetooth

Arduino RGB LED Bluetooth Control Using Android smartphone.
Control RGB LED using arduino uno and bluetooth easily.
Step by step Guide in the Following Link
Code- http://rztronics.com/control-rgb-led-using-bluetooth-and-arduino/
This is a Ope source code,You are allowed to modify it
Things you need-
Arduino
RGB LED
Bluetooth Module
Jumpers
Breadboard
Smartphone

source

Bluetooth module hc-05 with Arduino

Bluetooth module hc 05 with Arduino.
In this tutorial we will learn how we can connect bluetooth module hc-05 with arduino.
Code Link: http://hackaholic.info/bluetooth-module-hc-05-arduino/

source

Tutorial # 3: Configure & Interface Bluetooth Module with Arduino UNO in Urdu

This Tutorial Show you that how to configure a Bluetooth Module (HC-06) with AT Commands using Arduino and how to interface a Bluetooth Module (HC-06) with Arduino

Links:

Schematic 1 : http://adf.ly/1XjZTx
Schematic 2 : http://adf.ly/1XjZhZ
Arduino Sketch : http://adf.ly/1XjZrW
Android App : http://adf.ly/1XjZwq

source